Often asked: Where To Buy Trolling Motors Shafts?

Can you replace the shaft on a trolling motor?

If it is an Edge, Maxxum, or Fortrex it is replaceable. Screws into the top of the center section or brush end housing, depending on the motor. When unscrewing the old shaft, the shaft will be damaged where it cannot be reused.

Can a trolling motor shaft be too long?

However, if the shaft is too long, the propeller creates turbulence deep beneath the boat that will spook any nearby fish. And if the shaft is too short, the prop won’t be adequately submerged, which will create noisy chop in the water and also scare away the fish.

What is a trolling motor shaft made out of?

The tube contains a flexible shaft formed of three coils of phosphor bronze. This tube extends down and out into the water, where it carries a propeller, and at the inboard end an electric Motor is attached, which is itself driven by batteries.” It was invented and sold by the Electric Boat company.

You might be interested:  FAQ: What Products Does General Motors Produce?

How deep should a trolling motor be in the water?

Setting your trolling motor at an appropriate depth will help it to function properly, while at the same time reducing the risk of it becoming damaged. Remember, the general rule is to keep the motor submerged 12 inches below the waterline.

Can you replace the shaft on a Minn Kota trolling motor?

Re: DIY shaft replacement on a Minnkota You will need a pipe wrench or a special clamp to remove the shaft. Be sure to loctite (#271 Red) the shaft when installing it to the motor.

Can you shorten the shaft on a Minn Kota trolling motor?

Yes, in some cases but to maintain the warranty on your motor we recommend it be done by an Authorized Minn Kota Repair Center. Some models cannot have the shafts shortened.

How long should a trolling motor shaft be on a pontoon boat?

Most pontoon boats could really even get away with a 48″ shaft, but it is certainly better to go a little longer than you need. 55″ and 60″ trolling motor shafts are the most common for pontoon boats.

Can a trolling motor push a pontoon boat?

The good news is that, yes, you can, indeed put a trolling motor onto a pontoon boat. As long as you select the right shaft length and thrust (minimum 52 inches length and 55 lbs thrust), you should be good to go!

How fast will an electric trolling motor go?

The maximum speed of a trolling motor is 5 mph regardless of how many pounds of thrust.

Is a trolling motor considered a motor boat?

What Kind of Boat Must Be Registered? Generally, boats must be registered in their state if they have a gasoline, diesel or electric motor, including a trolling motor. Personal Watercrafts (PWCs) are considered motorized crafts and needs to be registered in most states.

You might be interested:  FAQ: What Motors Did The Chevy Cruze Come With?

What is the point of a trolling motor?

These work well when you actually are trolling, and your main goal is simply to move through the water at one to three MPH to give your lures or baits the proper presentation. In some cases transom mounted electric trolling motors may be used for the boat’s primary propulsion.

How do I know what size trolling motor I need?

To determine the right length for your boat, measure the distance from where the shaft is mounted on the deck or the transom to the water. Then add 16″ (for MotorGuide) or 20″ (for Minn Kota) and select the next closest measurement.

How fast is a 55 lb thrust trolling motor?

Assuming perfect riding conditions, the use of the best fuel i.e. the distillate marine diesel, and moderate load, 55-pound trolling motors are likely to attain a maximum speed of only 5 miles per hour.

How do I increase the speed of my trolling motor?

Make Your Trolling Motor Faster

  1. Make Your Trolling Motor Faster.
  2. Change the Battery.
  3. Reduce the Load of the Canoe.
  4. Fix a more Streamlined Propeller.
  5. Put on Lighter Attire.
  6. Replace the Existing Motor.
  7. Conclusion.

How far below the boat should the prop be?

If you have a short shaft motor, the top most part of the transom and the lower most part of the boat should be about 15 to 16 inches. For a long shaft, I think 20 to 21 inches is correct. Some mornings it just doesn’t seem worth it to gnaw through the leather straps.

Leave a Reply

Your email address will not be published. Required fields are marked *